Mosaic Tile Mounting Grid 3/8-Inch 10mm


hard plastic mounting grid for laying up designs of 3/8-inch tile on paper or mounting tape for rapid installation

In stock

SKU: mosaic-tile-mounting-grid-38-inch Categories: , , Tags: , ,


Mosaic Tile Mounting Grid 3/8-Inch (10mm) is for temporarily mounting 3/8-Inch tiles on paper or clear tape for rapid installation using the indirect method. NOT NEEDED FOR BEGINNERS. Most artists glue each tile directly on the surface they are covering and do not need grids. In fact, original mosaic art looks best when tile is cut into pieces and mounted in a pattern that is not a grid.

The grid mounts 841 mini glass mosaic tiles 3/8-inch (10mm) on a 1.15 square foot piece of mosaic mounting paper in a uniform grid of 29 x 29 tiles with a standard grout gap of approximately 1/32 inch.

Note that sockets of the grid has bevels at the edges which match those on the bottom edges of glass mosaic tile, such as found on most varieties of 3/8-inch metallic glass and vitreous glass tile. In other words, the grid might not work as well for 3/8-inch tile which is completely flat on the bottom, such as usually found on stone tile and porcelain tile. With the flat-bottomed stuff, you might have to be a little more careful to keep the tiles from popping out as you apply the mounting paper.

Mosaic Tile Mounting Grid 3/8 Inch

  • grid size: 29 tiles x 29 tiles.
  • grid area: approximately 1.15 square foot.
  • grout gap: approximately 1/32 inch.
  • tile size: 3/8 inch (10mm).

The Indirect Method

Mosaic tile can be glued one at a time DIRECTLY to a surface, or you can lay your mosaic out on a temporary surface in what is called the “Indirect Method.” Temporary surfaces can include things like fiberglass mesh, paper, adhesive contact paper, or trays filled with lime putty. Our grids were made to work with self-adhesive mounting tape or mounting paper that is temporarily glued to the faces of the tiles.

Why Use The Indirect Method

Why would you want to use the Indirect Method? It is easier to lay up your mosaic design at your work table than it is to lay it out on a floor or a wall or some other vertical surface. Also, you can work for days or weeks at your work table laying up the mosaic without tying up the location where the mosaic will actually be installed. Again, none of this is necessary for a beginner laying up a small craft project like a trivet or a mosaic mirror.

Use In Mosaic Art

The following is how to do the indirect method using our grids and mounting paper:

  1. Place glass mosaic tile into the grid face up, filling up the grid with your design.
  2. Dilute water-soluble glue such as Elmer’s Glue with 3 parts water to 1 part glue.
  3. Paint the water soluble glue onto the mounting paper using a small artists paint brush. Use a light coat to avoid wrinkling the paper.
  4. Lay mounting paper onto the face of the tile, careful to avoid wrinkles.
  5. Allow sheet to dry completely and remove from the grid.
  6. Spread thinset mortar or mosaic adhesive on the surface to be mosaiced.
  7. “Butter” the bottom of the sheet of tile with the same mortar or adhesive. Of coarse, you butter the bare glass bottoms of the tile, not the paper.
  8. Press the sheet of tiles into the adhesive-covered surface with the PAPER ON THE OUTSIDE.
  9. Allow the thinset or adhesive to cure for 24 hours.
  10. Mist the paper until it is soaked and peel it off the tiles.
  11. Grout the mosaic.

How To Make Mosaics

For more advice on designing your mosaic project or cutting and grouting tile, please see our Mosaic Frequently Asked Questions page or our How To Mosaic blog or our Mosaic Information Guide.